Buzzing Cooling Fan (ahhh!) >_<
Buzzing Cooling Fan (ahhh!) >_<
Hey, guys.
I have a cooling fan in my case that keeps buzzing. Do you have any idea why it does that?
I have a cooling fan in my case that keeps buzzing. Do you have any idea why it does that?
- Mobius
- DBB_Master
- Posts: 7940
- Joined: Sun Jun 03, 2001 2:01 am
- Location: Christchurch, New Zealand
- Contact:
Dust. Age. Low Quality.
Pick any combination or permutation.
Remove fan from case, Use soft-bristle brush to clean blades. Remove sticker from impellor centre. Remove circlip retaining the axle. Remove impellor. Use compressed air to clean motor windings. Apply TINY amount of VERY LIGHT oil. Replace impellor. Secure circlip. Place sticker back on impellor. Remount fan. Reboot.
Alternatively: buy high quality, low noice fan like Vantech Stealth.
Pick any combination or permutation.
Remove fan from case, Use soft-bristle brush to clean blades. Remove sticker from impellor centre. Remove circlip retaining the axle. Remove impellor. Use compressed air to clean motor windings. Apply TINY amount of VERY LIGHT oil. Replace impellor. Secure circlip. Place sticker back on impellor. Remount fan. Reboot.
Alternatively: buy high quality, low noice fan like Vantech Stealth.
-
- Defender of the Night
- Posts: 13477
- Joined: Thu Nov 05, 1998 12:01 pm
- Location: Olathe, KS
- Contact:
Actually, the thing probably isn't lubed right. Still, it won't hurt for it to have clean blades.
On the back of your fan should be a label sticker. Peel that back until you've gone past the center of the fan. There should be a rubber or plastic stopper. Use an exacto blade to pop that right off. Now what you do is put a couple drops in there and turn the blades a few times until its relatively smooth. Personally, I put a couple more drops in for good measure, but thats up to you. Don't fill it up all the way! Then put the stopper back on and wipe off any excess with a tissue. Then push the label sticker back down and you're good to go.
On the back of your fan should be a label sticker. Peel that back until you've gone past the center of the fan. There should be a rubber or plastic stopper. Use an exacto blade to pop that right off. Now what you do is put a couple drops in there and turn the blades a few times until its relatively smooth. Personally, I put a couple more drops in for good measure, but thats up to you. Don't fill it up all the way! Then put the stopper back on and wipe off any excess with a tissue. Then push the label sticker back down and you're good to go.
i just picked up a boxful of buzzing fans from a discard pile at a computer store, everysingle one works perfectly.
a few needed some bad work, so i lubed and ran them for at least 20 mins (some required a few runs of that proceedure) to allow the 3-in-1 to fully lubricate every surface and get the bearings back smooth
a few needed some bad work, so i lubed and ran them for at least 20 mins (some required a few runs of that proceedure) to allow the 3-in-1 to fully lubricate every surface and get the bearings back smooth
-
- Defender of the Night
- Posts: 13477
- Joined: Thu Nov 05, 1998 12:01 pm
- Location: Olathe, KS
- Contact:
Yeah, its amazing what those fans can take eh? People throw away perfectly good parts just because it requires a little effort to fix them.AceCombat wrote:i just picked up a boxful of buzzing fans from a discard pile at a computer store, everysingle one works perfectly.
a few needed some bad work, so i lubed and ran them for at least 20 mins (some required a few runs of that proceedure) to allow the 3-in-1 to fully lubricate every surface and get the bearings back smooth
- Vindicator
- DBB Benefactor
- Posts: 3166
- Joined: Mon Dec 16, 2002 3:01 am
- Location: southern IL, USA
- Contact:
I was workin on a computer for a friend, he had just bought it from a heavy smoker. The fans were covered with thick, brown sludge and had horrendous dust buildup (ever seen brown dust? it aint pretty). None of em worked right. I dont care if those fans could be salvaged, I wasnt willing to fix em up