Odd problem
- Liquid Fire
- DBB Ace
- Posts: 403
- Joined: Wed Oct 15, 2003 2:01 am
- Location: Los Gatos, CA, USA
- Contact:
Odd problem
Every once in awhile, my entire screen will turn pink. Through a bit of trial and error, I have found that actually tipping the computer can fix/alter the color. What, exactly, is going on here?
- Liquid Fire
- DBB Ace
- Posts: 403
- Joined: Wed Oct 15, 2003 2:01 am
- Location: Los Gatos, CA, USA
- Contact:
Yes, your VGA cable or connector is shot. When the screen turns pink it is because the green in the RGB signal drops out. That leaves only red and blue, hence the pink color..
An old 15 incher I used to have had this problem, I had to put a kink in the cable and tape it down to keep it making contact.
An old 15 incher I used to have had this problem, I had to put a kink in the cable and tape it down to keep it making contact.
- Warlock
- DBB 3D Artist
- Posts: 3370
- Joined: Wed May 12, 1999 2:01 am
- Location: Midland, Tx, U.S.
- Contact:
its the cable causeAceCombat wrote:it could also be the monitor itself losing the Green signal, and the cable could be just fine.
thats a cable prob tehre cause iv had it to happen befor and like Tricord i had mine bent up and tape to befor the wires in it finaley gave out.Liquid Fire wrote:I have found that actually tipping the computer can fix/alter the color.
u can try replaceing the cable or do like i did and cut the cable and get a 15pin svga connector and resoder the wires or get a new monitor
- Liquid Fire
- DBB Ace
- Posts: 403
- Joined: Wed Oct 15, 2003 2:01 am
- Location: Los Gatos, CA, USA
- Contact:
-
- Defender of the Night
- Posts: 13477
- Joined: Thu Nov 05, 1998 12:01 pm
- Location: Olathe, KS
- Contact:
Actually, having a kink in the cable is a problem. You've got a loose connection in your cable which needs to be fixed before it corrodes. Unfortunately, this means popping open the back of the monitor and CAREFULLY wiggle the connections from the cable to the monitor's mobo. DO NOT DO THIS WHILE THE MONITOR IS ON! If you don't encounter any problems, then wiggle the pins on the SVGA connector (after putting the cover of the monitor back on of course). If they remain stiff, then you'll either have to cut the plastic shielding and bend each wire individually or just bite the bullet and replace it entirely.
- Lothar
- DBB Ghost Admin
- Posts: 12133
- Joined: Thu Nov 05, 1998 12:01 pm
- Location: I'm so glad to be home
- Contact:
Notice he doesn't describe a kink anywhere.Liquid Fire wrote:Quote, me :"/me tries it...
...Ok people, move along. There's nothing to see here... "
That meant in in apparantly subtle terms, I wiggled the cable, which fixed it, and I freely admit my own stupidity. I think I was just expecting a long, complex answer. Not a simple thing.
-
- Defender of the Night
- Posts: 13477
- Joined: Thu Nov 05, 1998 12:01 pm
- Location: Olathe, KS
- Contact:
[Shrek]Naw, do ya think?[/Shrek]Ferno wrote:I hope you realize MD that there are capacitors that are inside the monitor that retain enough juice to kill, even with the monitor off for hours.
Alot of the boards I've seen have the larger caps away from the cable connections so he should be safe as long as he doesn't muck with the underside of the board where the caps are located. Its perfectly safe to touch the outside of the capacitors since there are no actual connections there. The only connections are on the bottom of the cap, which is where the pins are located. The metal cap on the top is a safety feature to keep the damn thing from blowing to pieces all over the place if you hook it in wrong or give it too much juice. If you really want to get paranoid, look up the specs for the SVGA connector and take an ohm meter to check each pin.
Lothar: I've dealt with this exact same problem on multiple occasions. 99% of the time, its because the cable was bent at 90° or sharper, which if left like this over time CAN produce a kink in the cable. When you try to bend it back, it'll snap one or more of the wires, which will sever the connection of one or more color signals resulting in the above. The very fact that he bent the cable to "fix" it proves that there is a loose connection in the cable somewhere.
- STRESSTEST
- DBB DemiGod
- Posts: 6574
- Joined: Sun Nov 21, 1999 3:01 am