Any who built the 3DP to USB adapter still about?

For system help, all hardware / software topics NOTE: use Coders Corner for all coders topics.

Moderators: Krom, Grendel

Post Reply
mattsimis
DBB Cadet
DBB Cadet
Posts: 6
Joined: Tue Mar 03, 2009 4:25 pm
Location: Ireland

Any who built the 3DP to USB adapter still about?

Post by mattsimis »

No one replying in the thread anymore. :(

I built it, twice, most recently using this image as its the most similar to my parts (ie the DSUB):
http://www.postimage.org/image.php?v=Ts1znUBJ

The Teensy v2 board can do its flashing tests just fine, but when I load 3DProR3.hex the LED just flashes faster and I get no new device in Windows.. nothing at all happens!?
User avatar
Grendel
3d Pro Master
3d Pro Master
Posts: 4390
Joined: Mon Oct 28, 2002 3:01 am
Location: Corvallis OR, USA

Post by Grendel »

Whoops, sorry. Ment to reply but somehow it got burried. What are the values of the caps & resistors you are using ? Can you post a picture of your build ?

Also, the device will flash the LED while it's trying to find a joystick. It will start USB enumeration after it found one. Did you try your build w/ a different joystick ?
ImageImage
mattsimis
DBB Cadet
DBB Cadet
Posts: 6
Joined: Tue Mar 03, 2009 4:25 pm
Location: Ireland

Post by mattsimis »

Ah hi, the man himself!

Since my PM to you I went out and got the exact Caps and Resistors (marked 222k Cap and 0.6w 2.2kOhm resistor), still the same :
Image
Image


Now I fully admit I may have made some very stupid mistake on all this!
User avatar
Grendel
3d Pro Master
3d Pro Master
Posts: 4390
Joined: Mon Oct 28, 2002 3:01 am
Location: Corvallis OR, USA

Post by Grendel »

Can't determine if the wiring is ok from the pics :/ Did you try a different joystick ? Are the caps really 2.2nF ? (1nF will work too, so will 1k resistors. The circuit is very tolerant to lower numbers, but not to higher ones.)
ImageImage
mattsimis
DBB Cadet
DBB Cadet
Posts: 6
Joined: Tue Mar 03, 2009 4:25 pm
Location: Ireland

Post by mattsimis »

I tried 1000pf Caps but 2watt 2.2kOHm resistors. Ill have to go buy more resistors to test lower.

I assume the Joystick works, was in a box here for years, I like it so much I never threw it out, but cannot test it else where either.
User avatar
snoopy
DBB Benefactor
DBB Benefactor
Posts: 4435
Joined: Thu Sep 02, 1999 2:01 am

Re:

Post by snoopy »

mattsimis wrote:I tried 1000pf Caps but 2watt 2.2kOHm resistors. Ill have to go buy more resistors to test lower.

I assume the Joystick works, was in a box here for years, I like it so much I never threw it out, but cannot test it else where either.
If you have more 2.2k's, just pair them and voala you have 1.1's.
User avatar
Spidey
DBB Grand Master
DBB Grand Master
Posts: 10808
Joined: Thu Jun 28, 2001 2:01 am
Location: Earth

Re:

Post by Spidey »

snoopy wrote:
mattsimis wrote:I tried 1000pf Caps but 2watt 2.2kOHm resistors. Ill have to go buy more resistors to test lower.

I assume the Joystick works, was in a box here for years, I like it so much I never threw it out, but cannot test it else where either.
If you have more 2.2k's, just pair them and voala you have 1.1's.
Parallel them…

Sorry, just really anal about those things. :wink:
User avatar
snoopy
DBB Benefactor
DBB Benefactor
Posts: 4435
Joined: Thu Sep 02, 1999 2:01 am

Post by snoopy »

Lets see, and the tolerancing doubles in accuracy, is that right?
Post Reply